• CPA36 - Power amplifier 360W 100V
  • CPA36 - Power amplifier 360W 100V

CPA36

DiscontinuedPower amplifier 360W 100V
Replaced by SCP224
  • 24 Volts emergency power operation
  • Advanced protection circuit
  • XLR input & linkthrough connections with gain control
  • Terminal block output connections ( 4Ω, 25V, 70V & 100V)
  • Class A/B amplifier technology
  • Ground lift switch
  • High-pass filter switch
5 years
Where to buy?

The CPA36 is a professional single channel 100V power amplifier with a power of 360 Watt, especially designed for most common 100V PA systems, and perfect to be used in combination with the CPR12 pre-amplifier. It is designed as a no-nonsense amplifier with only the necessary controls and connections. This creates great simplicity in use and installation. There are several power output taps available for use in 100V, 70V and even 4 Ohm Low impedance installations and they are fitted with an advanced multipurpose protection circuit. The protection circuit detects DC malfunction, short circuit, overheating, overload and limits the signal when necessary. Another present feature is the 24 V DC connection for powering the amplifier with emergency power when the main power is shut down. At the back of the amplifier, there are trim potentiometers to set the input level, a high pass filter switch and a ground lift switch provided. The input connection is made with balanced XLR connectors, and there’s a signal output for linking with other amplifiers. The steel 19" housing has a height of 2 HE.

Operation indicator LED's
Class A/B amplifier technology
Advanced protection circuitry
24V emergency power input
Terminal block output connections (100V, 70V, 25V & 4Ohm)
XLR input & linktrough connections
Input gain control potentiometer
High pass filter switch
CPA36 - Power amplifier 360W 100V

Technical specifications

System specifications
RMS/AES power handling 360 W
Frequency Response (± 3 dB) 70 Hz - 18 kHz
Signal / Noise > 90 dB
THD+N (@ 1 kHz) < 1%
Technology Class A/B
Power Supply Conventional (Transformer)
Source 230 ~ 240 V AC / 50 ~ 60 Hz (110~115 V AC / 50~60 Hz after connection change)
Inputs Sensitivity -12 dB ~ 0 dB
Impedance 10 kΩ balanced
Connector XLR female with Male Linkthrough
Outputs Voltage / Impedance 100 V / 28 Ω
70 V / 14 Ω
38 V / 4 Ω
Connector 4-pin Euro Terminal block (Pitch - 7.62 mm with locking)
Protection DC Short circuit
Over heating
Over load
Signal limiting
Cooling Dual speed controlled fan
Operating temperature 0° ~ 40° @ 95% Humidity
Product Features
Dimensions 18.98 x 3.46 x 12.99 " (W x H x D)
Weight 33.29 lb
Mounting 19”
Unit height 2 HE
Construction Steel
Colours Black
Accessories Included 4-pin Euro Terminal Block outputs connector
2-pin Euro Terminal Block 24V Power connector
Optional CPE100 Rack mount handles
Recommended applications
Bars & Restaurants
Retail
Corporate

FAQ

Answer

As the power consumption of an amplifier, strongly depends on how hard the amplifier is driven, measurements are provided for various loads: idle, 1/8 of average full power, 1/3 of average full power, and full power.

Idle 
Current draw at idle or with very low signal level

1/8 Power: Pink Noise
Amplifiers are tested using pink noise signals to simulate real-world speech and music signals.  It approximates operating with music or voice with light clipping and represents the amplifier's typical "clean" maximum level, without audible clipping. This 1/8 power signal provides a very good approximation of how hard an amplifier would be driven by typical real-world speech/music signals, assuming those signals were being driven as loud as possible without clipping the amplifier.

1/3 Power: Pink Noise
1/3 Power Pink Noise is similar to 1/8 Power Pink Noise, except that it is a significantly more powerful input signal. It approximates operating with music or voice with very heavy clipping and a very compressed dynamic range. This 1/3 power signal provides an approximation of how hard an amplifier would be driven by typical real-world speech/music signals, assuming those signals were being driven loud enough to clip the amplifier heavily, and produce severe, audible distortion.

Full Power
Current draw at full power is measured with a sine wave at its maximum possible level. However, it does not represent any real-world operating condition and represents the absolute extremes that an amplifier could ever experience.
 

Downloads

Information sheets other languages

Stay up to date with our activities

Latest news and case studies

Support

Just a click away.
Don't hesitate to contact us.

Contact us
Top